top of page

Redi-Rock vs Versa-Lok vs Keystone: Which Retaining Wall Block Fits Your Yard?

Writer: BRK Custom Concrete
BRK Custom Concrete
Nov 13
7 min read

Match the block to the wall height; unit size is the biggest difference between these retaining wall block types. A Versa-Lok Standard unit weighs 82 pounds on Versa-Lok's product page and a Keystone Compac III about 69 to 77 pounds in Keystone's construction manual, while Redi-Rock's data sheet describes its 28-inch blocks as "machine-placed" units, with full-size blocks weighing roughly 1,150 to 1,750 pounds each. Versa-Lok and Keystone state unreinforced heights of about 3 to 6 feet, each tied to soil and loading conditions; Redi-Rock's engineering FAQ gives far taller gravity design heights with favorable soils.

 

Each maker publishes its own height for a wall built without soil reinforcement, and each attaches conditions. Versa-Lok's FAQ says "In most situations, VERSA-LOK walls can be built three to four feet tall without engineering or soil reinforcement." Keystone's design manual (revised May 2020) says its walls may perform as gravity walls up to 6 feet with Standard units and up to 3.3 feet with Compac units, depending on geometry, soil type and loading. Redi-Rock's engineering FAQ puts the maximum design height of a standard block gravity wall at approximately 18 feet with favorable soil conditions, on a page written for engineers. Two code lines sit apart from all three: Pennsylvania's permit exemption covers walls up to 4 feet that support no surcharge, and the 2021 IRC, adopted in Pennsylvania, requires engineered design above 48 inches of unbalanced fill, or above 24 inches with lateral loads in addition to soil. None of these figures is a design for a particular yard. Below: specs, height limits, connections, code lines and yard fit.


Custom concrete patio installation process in Pittsburgh backyard with professional equipment and reinforcement placement

What Do Redi-Rock, Versa-Lok and Keystone Have in Common?

 

All three are segmental retaining wall systems. A segmental retaining wall is a wall of concrete units stacked without mortar that holds back soil through its own weight, with geogrid added when weight alone is not enough. A technical note from the Concrete Masonry and Hardscapes Association (CMHA), formed by the unification of ICPI and NCMA, says these walls "function as gravity structures by relying on self-weight" to resist retained soil and surcharge loads.

 

Versa-Lok gives its reason for skipping mortar: "Mortarless construction allows walls to remain flexible and accommodate minor earth movement (such as that caused by freeze/thaw cycles) without damage." An analysis of NOAA daily records for 1991 to 2020 counts about 82 days a year at Pittsburgh International Airport when the low drops to 32 degrees or colder and the high climbs back above freezing.

 

Poured concrete, timber and stone walls work differently; this comparison of retaining wall types for sloped properties covers them alongside block.

 

How Do the Three Retaining Wall Block Types Compare?

 

Each figure below comes from the maker's own document. Keystone notes that unit dimensions and weight vary by manufacturer, and Redi-Rock says actual weights will vary.

 

Block

Unit size and weight

How courses connect

Height without soil reinforcement, as the maker states it

Versa-Lok Standard

6 in high, 16 in face, 12 in deep; 82 lb

Friction from unit weight plus two Versa-Tuff pins per unit

4 ft maximum unreinforced for 12 in deep units in optimum conditions (product pages); three to four feet in most situations (FAQ)

Keystone Compac III

8 in high, 18 in wide, 12 in deep; about 69 to 77 lb

Two fiberglass pins per unit

Up to 3.3 ft, depending on geometry, soil type and loading

Keystone Standard III

8 by 18 in face, 18 or 21 in deep; about 80 to 99 lb

Two fiberglass pins per unit

Up to 6 ft, same conditions

Redi-Rock standard blocks

18 in high, 46 1/8 in long face; 28 in deep full units roughly 1,150 to 1,750 lb

Knob and groove: cast shear knobs seat in a channel in the block above

About 18 ft with favorable soils, a design height for engineers

 

How Tall Can Each Wall Go Before It Needs Geogrid?

 

All three makers tie height to soil and loads. Versa-Lok's FAQ says "Factors such as wall height and soil loads should be carefully considered before determining how you construct your wall," and that its walls "can be built to any required height with proper engineering and soil reinforcement."

 

Keystone's manual says soil reinforcement is required above its 6-foot and 3.3-foot gravity heights. For conventional gravity walls, its ICC-ES evaluation report, ESR-2113, adds: "Typical design heights are 2.5 to 3 times the depth of the unit being used." As a rough estimate from that ratio, a 12-inch-deep Compac unit works out to 30 to 36 inches (12 inches times 2.5 to 3), a little under the manual's 3.3 feet.

 

Redi-Rock's engineering FAQ says gravity walls of XL Hollow Core blocks can reach close to 21 feet with favorable soils; its Positive Connection (PC) system adds geogrid for taller walls, and "Under special conditions, and with additional engineering support," walls can be designed taller than 60 feet. Redi-Rock's installation guide supplements, and does not replace, a site-specific design by a Professional Engineer, and tells builders to "Obtain the necessary engineering and permits for the project."

 

Treat these as maker limits, not a plan for a given yard; an engineer assesses each site.

 

How Do the Blocks Lock Together and Step Back?

 

Setback is the distance each course steps back from the one below, leaning the wall into the slope it holds.

 

  • Versa-Lok: unit weight creates friction between courses, and two non-corrosive Versa-Tuff pins per unit add a mechanical connection. The Standard unit sets back 3/4 inch per course.

  • Keystone: two fiberglass pins per unit, per ESR-2113. The rear pin holes give a minimum setback of 1 inch per course; the middle pin hole gives a 1/8 inch minimum, close to vertical.

  • Redi-Rock: shear knobs cast into the blocks seat in a continuous channel in the block above. Standard 18-inch blocks step back 1 5/8 inches per course, a 5.2-degree batter.

 

Redi-Rock and Keystone both call for gluing cap units with an adhesive.

 

When Do Pennsylvania Code Lines Apply, Whatever the Block?

 

As of October 2026, Pennsylvania's Uniform Construction Code (UCC) uses the 2021 International Residential Code, adopted effective January 1, 2026. Section R404.4 of the 2021 IRC says walls not laterally supported at the top "that retain in excess of 48 inches (1219 mm) of unbalanced fill, or retaining walls exceeding 24 inches (610 mm) in height that resist lateral loads in addition to soil, shall be designed in accordance with accepted engineering practice." It also calls for a safety factor of 1.5 against lateral sliding and overturning.

 

The permit line is separate. Under 34 Pa. Code 403.62(c)(2), no UCC permit is needed for "Retaining walls that are not over 4 feet in height measured from the lowest level of grade to the top of the wall unless the wall supports a surcharge," provided the work does not violate a law or ordinance. The City of Pittsburgh's permit exemption page lists the same 4-foot line and surcharge condition, and says the work must still comply with the City Zoning Code.

 

Keystone's specifier also calls for structural design by a qualified engineer, and ESR-2113 says structural calculations must be submitted to the code official for each wall system installation.

 

Each municipality's code office confirms what applies on a given lot, and an engineer confirms the design; a separate post covers retaining wall permits.

 

Which Block Fits Which Yard?

 

Start with the finished height:

 

  1. A garden or yard wall about 3 to 4 feet tall. Versa-Lok retaining walls (three to four feet in most situations) and Keystone Compac (up to 3.3 feet) fit, under each maker's soil and loading conditions. Versa-Lok's product page gives an 8-foot minimum radius for curves.

  2. A wall between 4 and 6 feet. Keystone says Standard units may work as a gravity wall up to 6 feet, depending on geometry, soil type and loading. Past 4 feet, or with a surcharge, Pennsylvania's permit exemption no longer applies, and a wall retaining more than 48 inches of unbalanced fill falls under R404.4's engineering requirement; the code office and an engineer confirm both.

  3. A tall grade change. Redi-Rock's published heights are the highest of the three. A machine sets each block, so the job needs equipment access, and Redi-Rock's guide calls for a site-specific engineered design.

 

Height, soil, site access and drainage also move the price, as laid out in this look at what drives retaining wall installation cost. For walls near a house, see how retaining walls protect a foundation.

 

FAQ

 

How much does a Redi-Rock block weigh?

 

Redi-Rock's data sheet lists full-size 28-inch blocks at roughly 1,150 to 1,750 pounds each and half blocks at roughly 540 to 810 pounds. Redi-Rock's 41- and 60-inch blocks weigh more; the 60-inch data sheet lists full units at about 3,220 to 3,420 pounds.

 

How tall can a Versa-Lok wall be without geogrid?

 

Versa-Lok's FAQ says three to four feet in most situations, without engineering or soil reinforcement, and its Standard unit page lists a 4-foot maximum unreinforced height. An engineer weighs soil and loads on a given site.

 

Do Keystone blocks use pins?

 

Yes. Keystone's ESR-2113 report describes two fiberglass connection pins per unit, 0.5 inch in diameter and 5.25 inches long.

 

Are Versa-Lok blocks solid?

 

Yes. Versa-Lok's FAQ describes its units as solid and says corners, curves and steps can be built with one unit.

 

Do you need a permit for a 4-foot block wall in Pennsylvania?

 

Under 34 Pa. Code 403.62(c)(2), a retaining wall not over 4 feet, measured from the lowest level of grade to the top of the wall, needs no UCC permit unless it supports a surcharge. Local ordinances still apply, so confirm with the municipal code office before building.

 

Redi-Rock, Keystone and Versa-Lok Walls From BRK Custom Concrete

 

BRK Custom Concrete offers Redi-Rock Block, Keystone and Versa-Lok retaining wall systems for the Greater Pittsburgh Area, with professionally installed Redi-Rock block retaining walls designed for strength and visual appeal and Keystone retaining walls for managing slopes and preventing erosion. The company was founded in 2015 by Robert Kaczorowski, whose background includes 12 years of excavation and retaining wall jobs. Request a free quote with the planned wall height and length in hand.

 

Visit BRK Custom Concrete or call (412) 419-8123 today. Contact us for more information.


BRK Concrete

 
 
 

Comments


bottom of page